Speaker Break In Download
You may Download each track once, your access to your down load is limited to one day. Forwarding your download will encrypt the download to and makes the tracks inoperable. Sharing, Burning or forwarding your download is strictly prohibited and not advisable. Each Track and the download as a whole is copyright protected by the Digital Millennium Act.
Forwarded Downloads are tracked and violators will be prosecuted.
Read the download instructions at the bottom of this page.
Applies to any size Guitar, Bass, PA, Pro- Audio, Hi-Fi, Home Audio, Car Audio and Commercial Audio Speaker or Speaker set ups.
The EarCandy speaker break in tool is professionally engineered so that you do not have to match the speaker’s voltage requirement. It runs 5 to 65 cycle variations with crossed phase polarities. The cross phased polarities persuade the cone to wiggle back and forth in its X-max at high and low rates of speed sets.
This process duplicates playing through the speaker for 10 hours at approximately 50 watts, however this tool achieves this at very low to moderate volume levels that can be tolerated by your family and pets. You can isolate your cab and amp in a bedroom (even in an apartment) and the achieved break in result of playing this 75 minute CD is the same as playing for 10 hours at very high volume levels.
Running the tracks 4 times for a total of 300 minutes (5 Hours) will achieve the same result as playing through the speaker at its rated wattage level for 40 hours.
Simply play the CD or downloaded tracks into your amplifier with the amp set up as clean as possible. Do not add any gain to the amp channel. Plug the signal cable from the CD or MP3 player into your guitar, bass or PA amp with the amp set as clean as possible. Turn the amp up to no more than 5 watts. Playing the cd loud or at more than 5 watts is ok, but we do not recommend it as it is not necessary for the speaker break in CD to be played loud to accomplish its optimum performance and goal.
The EarCandy.Com Speaker break in tool is invaluable because once you own the tracks, you can use it an unlimited amount of times on new cabs, new speaker installs and you never have to pay for an incorrectly executed overpriced factory break in process again.
The first 75 minute run will warm the speaker’s response and take the harsh crispiness off of the top end and greatly improve sustain, The Second 75 Minute run will further exercise the cone and surround, extending the bass response of the speaker (or speakers if you have a 2x or 4x guitar speaker cabinet)
The third 75 Minute run will further exercise the cone, surround spyder and voice coil increasing warmth, body, sustain, clarity and tone of the speaker or speakers and the fourth 75 minute run will polish off any remaining stiff components and finalize your speakers break in time.
We employed this on new speakers we installed in cabs and delivered these speaker cabs to performing artists that would throw the speaker right into the mix in live and studio settings and amazed performers, producers and sound men alike. You can play the tracks through your speaker cab using your computers headphone out, a home stereo or CD player with the headphone out going to your amp (Simply Burn the tracks onto a CDRW). The tracks do not have to be played loud for it to work. The files are MP3 files so an MP3 player may also be used for your convenience. If you burn the tracks onto a CD, any CD player will work the tracks just the same.
Other companies that offer factory broken in speakers run the speaker at abusive volume levels to the point where they have to stop the process and let the speaker cool down for an hour. This is not recommended and will shorten the life of the motor structure leading to eventual total failure of the speaker. It is akin to overheating a new automobile engine and then letting it cool off for an hour.
The way the EarCandy speaker break in tool was produced, creates simulated decibel levels as high as 140db at wattage levels as low as 2 to 5 watts, preventing over heating of the voice coil, avoiding damage that may not show up for 6 months to a year. The End result of employing this speaker break in download is larger Bass and low mids and mid-range response with warmer clarity, articulation, depth and definition. It also provides subtle reduction in high end frequencies that sound harsh and undesirable to the ear.
This process also softens the cone, surround spyder and motor structure providing more sustain and body to the overall tone of ANY guitar speaker. All without blaring the speaker with un necessary wattage levels that can cause unforeseen damage in the future life of the speaker because the voice coil is never over heated. The coil is warmed, so it will expand and contract slightly, creating a safe, fast and proper coil break in with NO possibility of any damage in the long term.
If you notice, many speaker companies provide only a 1 year warranty and this is because the damage that occurs when the break in process is overdone and inevitably can and will cause total failure of the speaker motor structure. EarCandy guarantee’s this will not happen when our speaker break in tool is implemented correctly. Our guitar speaker break in is very simple and easy to use quietly and provides a safe, thorough, quiet and fast break in process that will allow you to enjoy your speaker or speakers for a lifetime.
An unforeseen benefit of this guitar speaker break in tool was when we employed it into guitar speaker cabs that had been used for years with only certain genres of music, the break in tool exercised those speakers in ranges the speakers had never experienced and raised the overall tone and performance level of speakers professional performers thought had been broken in for a long time. We like to look at it like a Guitar speaker break in and subsequent guitar speaker tune up tool. The Tune up on speakers that have been played through for years only took one 75 minute run.
We have spent a LARGE amount of $ and time to develop and copy right this speaker break in tool to work for Guitar, Bass, Car Audio, Home Audio, Commercial Audio & P.A. Speaker break in for applications such as ceiling speakers, public announcement speakers in school and college campus buildings and places of work like call centers, factory’s, department stores, shopping malls and more. If you are needing a Keyboard or Acoustic guitar speaker break in tool, utilizing this speaker break in tool will deliver the same desired effect.
- Click on the speaker download tab in the menu
- Click “Add to cart”
- Then, in the green bar at the top of the page, click “View Cart”
- Then, click “proceed to checkout”
- Enter your billing and shipping information, don’t forget to click the terms and condition’s box
- Click proceed to PayPal
- If you dont have a Paypal account, you can pay with a credit or debit card
- Once the payment is accepted, it will take you to a screen that has all the break in tracks with “download” next to them, this is where and how you can down load each track. The picture below is what the down load page looks like.
- Down them immediately, there is a time limit and download limit for each purchase.
If you require this product on CD and would prefer to order it that way, Please click HERE
To hear a sample of the download, please click the play button in the lower left corner of this page.