4×12 Parallel Wiring Harness

The 4×12 Parallel Wiring harness

  • This harness wires four 16 ohm speakers to 4 ohms mono.
  • DO NOT USE 8 OHM SPEAKERS WITH THIS HARNESS.
  • Designed for use with any guitar 4×12 speaker cab.
  • Many 4×12 cabs use cheap input jacks with 20 gauge aluminum strand
  • This harness is 14 gauge OFC pure copper.
  • We point to point hand wire and solder every harness with silver solder.
  • This harness comes with a paper diagram, making re wiring your cab fast & easy.
  • This Harness comes ready to install
  • We use the very best Neutrik brand input jacks.
  • Built with an extra foot of cable  for an easier install.
  • Hand soldered with silver solder, tested and shipped with in 24 hours of your order.

If you are not remotely familiar with soldering, the wiring harness with wire tabs installed is a better, safer choice. You will receive the wiring diagram complete with a 6 step check list, assembled harness with input jack.

The EarCandy Power Pig amp attenuator

“The Power Pig”
This is an amp attenuation device that takes no AC adapter, no batteries, no confusing switches buttons or dials.

The EarCandy Power Pig 8 Ohm amp attenuator is very easy to use, Simply plug your amps speaker out into the amp in on the Power Pig and then plug your cabs speaker cable into the cab in on the Power Pig and Viola, 50% amp attenuation. Complete with rubber non skid pads on the bottom. This will harmlessly cut the volume of your amp in half with our sacrificing tone, Over Drive, FX or distortion.

  • It ha Ceramic thermal capacity to ensure cool running and long life
  • It has Tight impedance tolerances
  • The Ultra easy operation and durable design make the Power Pig an ideal choice for players who want that searing distortion at half the volume without constantly having to hear “TURN IT DOWN!”
  • The Power Pig Is designed with the low to mid wattage boutique amps in mind. Detailed attention to high and Low frequencies, at Bedroom and apartment studios, Is the key function of The Power Pig. Many hours of testing with my Fender’s and Egnater’s Even at the lowest volume settings all of the high mid and low frequency’s deliver stunning results because you control those parameters with your amps tone stack – as it should be.

    There are no switches to flip or buttons to push, no power cable or battery pack. Just plug the output from your amplifier into the Amp in and your speaker into the speaker out and your amp is attenuated at 50% its normal volume (the out put is cut in half. Creating A true bedroom volume practice amp from any loud or gain amp.(The Power Pig is Pat. Pending)

    The Power Pig

    “The Power Pig” This is an amp attenuation device that takes no AC adapter, no batteries, no confusing switches buttons or dials. The EarCandy Power Pig 8 Ohm amp attenuator is very easy to use, Simply plug your amps speaker out into the amp in on the Power Pig and then plug your cabs speaker[…]

    About EarCandy

      EarCandy is a family company that has revolutionized Guitar & Bass audio speaker cabinets and wiring. Established in 2002, we evolved American made speaker cabinets from unnecessarily oversized, overpriced and overweight typical designs that your granddad used, to light, affordable and road worthy world class tone machines. All materials are obtained from American manufacturers,[…]

    1×8 1×12 1×15 1×18 Bass Wiring Harness

    The 1x Bass wiring harness

    • This Harness will work with any 1x configuration.
    • This harness does not affect the ohm load, The speaker determines the ohm load.
    • Designed for use with any Bass guitar  speaker cab.
    • This harness is 14 gauge OFC pure copper / silver strand Acoustic Research speaker cable.
    • We point to point hand wire and solder every harness with silver solder.
    • This harness comes pre soldered tips on the connection end
    • + and – ( + white striped side and – side with no stripe )
    • This harness comes with a diagram, making re wiring your cab fast & easy.
    • This Harness comes ready to install with solder on the speaker wire for you.
    • We use the very best Lichtenstein Neutrik Speakon & 1/4″ combo input jacks.
    • This Input will take speakon or 1/4″ speaker cable
    • This will pass all codes domestic and over seas.
    • Built with an extra foot of cable for an easier install.

    All of the parts of this wiring harness are made in the USA** and are the same top quality materials we use in our Premium guitar and Bass speaker cabs. The Lichtenstein’s are made in Germany, we use them because they are the very best and have a lifetime warranty.

    You will receive the wiring diagram complete with a check list, assembled harness, Jack plate cup, Screws, internal speaker wire clamp and input jack, all assembled. Satisfaction Guaranteed! All Harness’s will ship within 24 hours or less, with tracking emailed to you.

    Summer Cab Sale 2017

    Please check out our Summer CAB Sale – Now through August 30 2017 We have: Sovereign 1×12 Guitar Cabs Sovereign 1×12 Bass Cabs BuzzBomb 2×12 Guitar BassBomb 2×12 Bass Our Speaker break In down load is also for sale here – Speaker Break In Download All on SALE with Shipping included on guitar and bass[…]